Risco-group GT490X Manual do Utilizador

GT490XControl PanelQuick Start InstructionsDownload the complete GT490X Engneer’s Ref. Guide atwww.riscogroup.co.ukRISCO Group UK LtdTel: 0161 655 550

Engineer Programming ModeEngineer ProgrammingTo enter the engineer programming mode follow the steps outlined below:-1. Remove all power from the syst

The display will then show:-5. Select either 1 or 2 depending on which standard you require.The display will show:-6. Enter Engineer code.(1234 defaul

Page 11Note: Throughout the programming routine you may use the 0 (zero) Key toescape back one level. This does not apply when a numeric entry isexpec

Below is shown some of the Headers (menu numbers, see page 14) that are availableand the options that appear under each Header.Please refer to the GT4

Panic / DuressPA Mode / Bells Only / Bells AlwaysSilent Always / Bells if Line FaultTestable / Non-TestablePA Confirm (PA Confirm is defaulted to Off)

Common Options With Menu NumbersYou are able to jump to various common options when programming by entering the relevant menu numbers. With a Header s

Page 15Programming Alarm ConfirmThis section is used to program options that are relevant to BS8243. Beforeprogramming these options please take time

KeypadOpening (default = Always On) This controls the keypad option during Entry/Alarm, and controls whether thekeypad will lock-out during entry or i

Page 17Ace Low Battery (default = On)Options are On or Off. This option allows for the use of new control panel boards withV5.1 or later software to b

Page 18Other BS8243 Notes to ConsiderWhen a system auto re-arms with a zone in fault condition The GardTec control panelwill omit the zone concerned.

IMPORTANT!Input: GT490X AC230V +/-10% ~50Hz 125mA Max. 35W MaxNominal Temp Range: 0 - 50°CHumidity 70% non condensingGT490X Metal For Indoor Use OnlyT

Typical Wiring ModesWhere Anti-Mask detectors are used, one of the below wiring modes may be utilised.ELF1 wiring is used for detectors that have arel

PD6662:2010 Update - new featuresEN50131-1 2006 and BS8243Page 20PD 6662, the document describing how the European standards for Intrusion andHold-up

Keypad disabled for 90 seconds.The keypad will monitor the number of attempts without a valid User Code beingentered. More than seven attempts will ca

NotesPage 22PR5846 Rev12 490X QS Eng.qxd 10/05/2012 11:39 Page 23

GT490XPR5846 Rev12 490X QS Eng.qxd 10/05/2012 11:39 Page 24

Page 2IntroductionThe GT490X Control Panel is a microprocessor based unit that has been designed tobe suitable for all types of domestic and commercia

Output Terminal DescriptionsSpeaker TerminalsThis pair of terminals provide connection for:-System Speaker(s)Optional 16/32 Ohm Panel SpeakerA speaker

Remote KeypadsUp to four remote keypads may be fitted to the GT490X control panel. Each Keypadoffers a 32 character backlit LCD.A four core connection

- + - STROBE BELL BELL SAB PGM1 SPR+ SPR + - HOLD TMPR

Fig.5 Control Panel Input (Zone) ConnectionsFig.4 Typical Novagard 2G/4G ConnectionsPage 6+12V0VS-ST-R TMPF TMPBELL+BELL-SAB TMPBELLHOLD-STROBE-GT490X

Page 7Zone DoublingDetector on Zone 1 will be Zone 1 and the Doubled Zonewill be Zone 9.The first detector on Zone 2 will be Zone 2 and the DoubledZon

Page 8Initial Power UpWhen the Control Panel is powered up it will be either set or unset dependent on thestate of the Control Panel when it was power